AS 2699.1 pdf download
AS 2699.1 pdf download.Built-in components for masonry construction 1.1 Scope This Standard specifies requirements for wall ties for use in tying together — (a) the leaves of cavity masonry walls; (b) masonry veneer walls and loadbearing frames; and (c) masonry veneer walls against a strong backing wall. This Standard applies to wall ties used in masonry described in AS 3700,...
AS 2699.2 pdf download
AS 2699.2 pdf download.Built-in components for masonry construction 1.3 Terms and definitions For the purpose of this Standard, the definitions below apply. 1.3.1 batch clearly identifiable collection of units, manufactured consecutively or continuously under the same conditions, using material or compound to the same specification 1.3.2 capacity design procedure design method in which elements of the primary lateral earthquake-force-resisting system...
AS 1391 pdf download
AS 1391 pdf download.Metallic materials — Tensile testing — Method of test at room temperature 1 Scope This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature. NOTE Annex A contains further recommendations for computer controlled testing machines. 2 Normative references The following documents,...
AS 1735.4 pdf download
AS 1735.4 pdf download.Lifts, escalators and moving walks 1 Scope 1.1 This standard specifies the safety rules for the construction and installation of permanently installed new electric service lifts with traction or positive drive, or hydraulic service lifts defined as lifting equipment, serving defined landing levels, having a car, the interior of which is regarded as inaccessible to persons on...
AS 1337.0 pdf download
AS 1337.0 pdf download.Personal protective equipment 1 Scope This document defines and explains the principal terms used in the field of personal eye and face protection. 2 Normative references There are no normative references in this document. 3 Terms and definitions ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform:...
AS 2341.12 pdf download
AS 2341.12 pdf download,Methods of testing bitumen and related roadmaking products 1 Scope The objective of this Test Method is to specify the procedures for the determination of the penetration of bitumen and related roadmaking products. It is applicable to bituminous materials with penetrations less than or equal to 200 (0.1 mm). 2 Application ASTM D5/D5M-19 is the 2019 edition....
AS 2341.3 pdf download
AS 2341.3 pdf download.Methods of testing bitumen and related roadmaking products 1 Scope The objective of this Test Method is to specify procedures for the determination of kinematic viscosity of bituminous materials having kinematic viscosities in the range 6 mm 2 /s to 100 000 mm 2 /s (approximate dynamic viscosities 0.006 Pa.s to 100 Pa.s) using four different types...
AS 1012.25.1 pdf download
AS 1012.25.1 pdf download.Methods of testing concrete 4 Apparatus and materials 4.1 Measure 4.1.1 General The measure shall be made of metal not less than 3 mm thick, be watertight and be sufficiently rigid to maintain its shape with rough usage. The inside surface shall be smooth and free from corrosion. The rim of the measure shall be machined to...
AS 1571 pdf download
AS 1571 pdf download.Copper — Seamless tubes for air- conditioning and refrigeration 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. . 3.1 coil annealed copper tube supplied in a coiled form EXAMPLE Pancake coil, wound pack, or pair coil. 3.2 may indicates the existence of an option 3.3 mean outside diameter half...
AS 1301.457 pdf download
AS 1301.457 pdf download.Methods of test for pulp and paper 3 Terms and definitions For the purpose of this Standard the following terms and definitions apply. 3.1 lot aggregate of paper or board or pulp of a single kind with specified characteristics produced under conditions that are presumed uniform, and available for sampling at one time 3.2 may indicates the...